Edge-Core ES3528M-SFP Guía de instalación Pagina 488
- Pagina / 644
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Command Line Interface
4-192
4
• sort - Sort by address, vlan or interface.
Default Setting
None
Command Mode
Privileged Exec
Command Usage
• The MAC Address Table contains the MAC addresses associated with each
interface. Note that the Type field may include the following types:
- Learned - Dynamic address entries
- Permanent - Static entry
- Delete-on-reset - Static entry to be deleted when system is reset
• The mask should be hexadecimal numbers (representing an equivalent bit
mask) in the form xx-xx-xx-xx-xx-xx that is applied to the specified MAC
address. Enter hexadecimal numbers, where an equivalent binary bit “0”
means to match a bit and “1” means to ignore a bit. For example, a mask of
00-00-00-00-00-00 means an exact match, and a mask of
FF-FF-FF-FF-FF-FF means “any.”
• The maximum number of address entries is 8191.
Example
mac-address-table aging-time
This command sets the aging time for entries in the address table. Use the no form
to restore the default aging time.
Syntax
mac-address-table aging-time seconds
no mac-address-table aging-time
seconds - Aging time. (Range: 10-30000 seconds; 0 to disable aging)
Default Setting
300 seconds
Command Mode
Global Configuration
Command Usage
The aging time is used to age out dynamically learned forwarding information.
Console#show mac-address-table
Interface Mac Address Vlan Type
--------- ----------------- ---- -----------------
Eth 1/1 00-12-cf-94-34-de 1 Delete-on-reset
Trunk 2 00-12-cf-8f-aa-1b 1 Learned
Console#
- Powered by Accton 1
- Fast Ethernet Switch 3
- ES3528M-SFP 4
- E012008-DG-R01 4
- 149100035500A 4
- About This Guide 5
- Contents 24
- Chapter 1: Introduction 33
- Introduction 34
- System Defaults 38
- Connecting to the Switch 41
- Required Connections 42
- Basic Configuration 43
- Setting Passwords 44
- Setting an IP Address 44
- Dynamic Configuration 45
- Initial Configuration 46
- Trap Receivers 47
- Saving Configuration Settings 48
- Managing System Files 49
- Using the Web Interface 51
- Home Page 52
- Panel Display 53
- Main Menu 54
- Manual Configuration 67
- Using DHCP/BOOTP 68
- Enabling Jumbo Frames 69
- Managing Firmware 69
- Console Port Settings 73
- Telnet Settings 75
- Configuring Event Logging 78
- Remote Log Configuration 80
- Simple Mail Transfer Protocol 81
- Resetting the System 83
- Setting the System Clock 84
- Configuring NTP 85
- Setting the Time Zone 87
- Enabling SNMP Agent Status 91
- Setting the Local Engine ID 92
- Specifying a Remote Engine ID 93
- Configuring SNMPv3 Users 93
- Configuring SNMPv3 Groups 96
- Setting SNMPv3 Views 99
- Configuring the Switch 100
- User Authentication 101
- Configuring Encryption Keys 107
- Configuring AAA Accounting 110
- AAA Accounting Update 112
- AAA Accounting Exec Settings 115
- AAA Accounting Summary 115
- Authorization Settings 117
- Authorization EXEC Settings 118
- Authorization Summary 118
- Configuring HTTPS 119
- Configuring the Secure Shell 121
- Configuring the SSH Server 124
- Generating the Host Key Pair 125
- Importing User Public Keys 126
- Configuring Port Security 130
- Displaying 802.1X Statistics 137
- Web Authentication 138
- MAC Authentication 148
- Access Control Lists 149
- Setting the ACL Name and Type 150
- Configuring a Standard IP ACL 151
- Configuring a MAC ACL 155
- Port Configuration 160
- Creating Trunk Groups 164
- Configuring LACP Parameters 168
- Displaying LACP Port Counters 170
- Configuring Port Mirroring 177
- Configuring Rate Limits 178
- Showing Port Statistics 179
- Address Table Settings 183
- Displaying the Address Table 184
- Changing the Aging Time 186
- Displaying Global Settings 188
- Configuring Global Settings 191
- Displaying Interface Settings 194
- VLAN Configuration 205
- Assigning Ports to VLANs 206
- Displaying Current VLANs 209
- Creating VLANs 211
- Private VLANs 223
- Configuring Private VLANs 225
- Associating VLANs 226
- Protocol VLANs 229
- Link Layer Discovery Protocol 231
- transmission-interval 232
- Displaying Device Statistics 239
- Layer 2 Queue Settings 241
- Priority 243
- 13. CLI shows Queue ID 243
- Enabling CoS 244
- Selecting the Queue Mode 245
- Layer 3/4 Priority Settings 246
- Enabling IP DSCP Priority 247
- Mapping DSCP Priority 248
- Quality of Service 249
- Configuring a Class Map 250
- Creating QoS Policies 253
- VoIP Traffic Configuration 257
- Configuring VoIP Traffic Port 258
- Configuring Telephony OUI 261
- Multicast 262
- Multicast Filtering 263
- Enabling IGMP Immediate Leave 265
- IGMP Filtering and Throttling 270
- Multicast VLAN Registration 275
- DHCP Snooping 282
- DHCP Snooping Configuration 283
- IP Source Guard 287
- IP Clustering 290
- Cluster Configuration 291
- Cluster Member Configuration 292
- Cluster Member Information 293
- Cluster Candidate Information 293
- UPnP Configuration 295
- Accessing the CLI 297
- Console Connection 297
- Telnet Connection 298
- Entering Commands 299
- Command Line Interface 300
- Partial Keyword Lookup 301
- Using Command History 301
- Understanding Command Modes 301
- Exec Commands 302
- Configuration Commands 303
- Command Line Processing 305
- Command Groups 306
- Line Commands 307
- General Commands 316
- System Management Commands 322
- User Access Commands 333
- IP Filter Commands 335
- Web Server Commands 337
- Telnet Server Commands 340
- Secure Shell Commands 341
- Event Logging Commands 350
- SMTP Alert Commands 356
- Time Commands 360
- System Status Commands 373
- Frame Size Commands 379
- Flash/File Commands 380
- Authentication Commands 386
- RADIUS Client 389
- TACACS+ Client 393
- AAA Commands 397
- Port Security Commands 406
- 802.1X Port Authentication 407
- Access Control List Commands 434
- IP ACLs 435
- MAC ACLs 439
- ACL Information 444
- SNMP Commands 445
- Interface Commands 462
- Mirror Port Commands 473
- Rate Limit Commands 475
- Link Aggregation Commands 476
- Address Table Commands 486
- LLDP Commands 489
- Console(config)# 494
- refresh-interval 495
- UPnP Commands 511
- Spanning Tree Commands 513
- 515
- VLAN Commands 534
- Editing VLAN Groups 538
- Configuring VLAN Interfaces 540
- Displaying VLAN Information 546
- Priority Commands 560
- Quality of Service Commands 568
- Voice VLAN Commands 576
- Multicast Filtering Commands 583
- IGMP Query Commands (Layer 2) 588
- Console(config)#mvr 601
- IP Interface Commands 605
- IP Source Guard Commands 609
- DHCP Snooping Commands 613
- IP Cluster Commands 620
- Software Features 625
- Management Features 626
- Standards 626
- Management Information Bases 627
- Software Specifications 628
- Appendix B: Troubleshooting 629
- Using System Logs 630
- Glossary 631
- Glossary-6 636
- Virtual LAN (VLAN) 636
Relacionado con productos y manuales para Los conmutadores de red Edge-Core ES3528M-SFP
(20 paginas)
(32 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.371 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales