Edge-Core ES3628C Información técnica Pagina 436
- Pagina / 674
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Command Line Interface
4-110
4
Related Commands
snmp-server location (4-110)
snmp-server location
This command sets the system location string. Use the no form to remove the
location string.
Syntax
snmp-server location text
no snmp-server location
text - String that describes the system location.
(Maximum length: 255 characters)
Default Setting
None
Command Mode
Global Configuration
Example
Related Commands
snmp-server contact (4-109)
snmp-server host
This command specifies the recipient of a Simple Network Management Protocol
notification operation. Use the no form to remove the specified host.
Syntax
snmp-server host host-addr [inform [retry retries | timeout seconds]]
community-string [version {1 | 2c | 3 {auth | noauth | priv} [udp-port port]}
no snmp-server host host-addr
• host-addr - Internet address of the host (the targeted recipient).
(Maximum host addresses: 5 trap destination IP address entries)
• inform - Notifications are sent as inform messages. Note that this option is
only available for version 2c and 3 hosts. (Default: traps are used)
- retries - The maximum number of times to resend an inform message if
the recipient does not acknowledge receipt. (Range: 0-255; Default: 3)
- seconds - The number of seconds to wait for an acknowledgment before
resending an inform message. (Range: 0-2147483647 centiseconds;
Default: 1500 centiseconds)
• community-string - Password-like community string sent with the
notification operation to SNMP V1 and V2c hosts. Although you can set this
string using the snmp-server host command by itself, we recommend that
you define this string using the snmp-server community command prior
Console(config)#snmp-server location WC-19
Console(config)#
- Powered by Accton 1
- Fast Ethernet Switch 3
- F3.1.0.18 E032005-R02 4
- 149100005100H 4
- Contents 5
- Chapter 1: Introduction 29
- Introduction 30
- System Defaults 35
- Connecting to the Switch 39
- Required Connections 40
- Basic Configuration 41
- Setting Passwords 42
- Setting an IP Address 42
- Dynamic Configuration 43
- Initial Configuration 44
- Trap Receivers 45
- Saving Configuration Settings 46
- Managing System Files 47
- Using the Web Interface 49
- Home Page 50
- Configuration Options 51
- Panel Display 51
- Main Menu 52
- Manual Configuration 66
- Using DHCP/BOOTP 67
- Managing Firmware 68
- Console Port Settings 73
- Telnet Settings 75
- Configuring Event Logging 77
- Remote Log Configuration 78
- Displaying Log Messages 80
- Resetting the System 82
- Setting the System Clock 83
- Setting the Time Zone 84
- Enabling the SNMP Agent 86
- Console(config)# 87
- Setting a Local Engine ID 91
- Specifying a Remote Engine ID 91
- Configuring SNMPv3 Users 92
- Configuring SNMPv3 Groups 96
- Configuring the Switch 100
- Setting SNMPv3 Views 100
- User Authentication 101
- Configuring HTTPS 106
- Configuring the Secure Shell 108
- Generating the Host Key Pair 109
- Configuring the SSH Server 111
- Configuring Port Security 113
- Displaying 802.1X Statistics 120
- Access Control Lists 124
- Setting the ACL Name and Type 125
- Configuring a Standard IP ACL 125
- Configuring a MAC ACL 129
- Configuring ACL Masks 131
- Configuring an IP ACL Mask 132
- Configuring a MAC ACL Mask 134
- Port Configuration 136
- Creating Trunk Groups 141
- Configuring LACP Parameters 146
- Displaying LACP Port Counters 149
- Configuring Port Mirroring 155
- Configuring Rate Limits 156
- Showing Port Statistics 157
- Address Table Settings 161
- Displaying the Address Table 162
- Changing the Aging Time 164
- Displaying Global Settings 165
- Figure 3-67 STA Information 167
- Configuring Global Settings 168
- Displaying Interface Settings 172
- VLAN Configuration 183
- VA: VLAN Aware 184
- VU: VLAN Unaware 184
- Displaying Current VLANs 187
- Creating VLANs 188
- Configuring Private VLANs 194
- Configuring Protocol Groups 196
- Mapping Protocols to VLANs 197
- Layer 2 Queue Settings 198
- Figure 3-86 Traffic Classes 201
- Selecting the Queue Mode 202
- Layer 3/4 Priority Settings 204
- Mapping IP Precedence 205
- Mapping DSCP Priority 206
- Mapping IP Port Priority 208
- Quality of Service 209
- Configuring a Class Map 210
- Creating QoS Policies 213
- Multicast 217
- Multicast Filtering 219
- L3 - network core 225
- Displaying the DNS Cache 234
- Provides IP address 235
- Addresses 237
- Configuring Address Pools 239
- Displaying Address Bindings 243
- Master Router 244
- Backup Router 244
- Configuring Router Redundancy 245
- Configuring VRRP Groups 245
- IP Routing 253
- IP Switching 254
- Routing Path Management 255
- Routing Protocols 255
- Address Resolution Protocol 259
- Basic ARP Configuration 260
- Displaying Local ARP Entries 263
- Displaying ARP Statistics 264
- IP Statistics 265
- ICMP Statistics 267
- UDP Statistics 269
- TCP Statistics 270
- Configuring Static Routes 271
- Displaying the Routing Table 272
- Autonomous System A 283
- Autonomous System B 283
- Configuring OSPF Areas 287
- Configuring OSPF Interfaces 292
- Configuring Virtual Links 296
- Configuring NSSA Settings 303
- Console# 307
- Multicast Routing 309
- Configuring DVMRP 313
- Configuring PIM-DM 320
- Accessing the CLI 327
- Console Connection 327
- Telnet Connection 327
- Command Line Interface 328
- Entering Commands 329
- Showing Commands 330
- Partial Keyword Lookup 331
- Using Command History 331
- Understanding Command Modes 332
- Exec Commands 332
- Configuration Commands 333
- Command Line Processing 335
- Command Groups 336
- Line Commands 337
- General Commands 346
- System Management Commands 351
- User Access Commands 353
- IP Filter Commands 355
- Web Server Commands 357
- Telnet Server Commands 360
- Secure Shell Commands 360
- Event Logging Commands 369
- SMTP Alert Commands 375
- Time Commands 379
- System Status Commands 383
- Frame Size Commands 389
- Flash/File Commands 390
- Authentication Commands 395
- Authentication Sequence 396
- RADIUS Client 398
- TACACS+ Client 401
- Port Security Commands 403
- 802.1X Port Authentication 405
- Access Control List Commands 413
- IP ACLs 414
- MAC ACLs 425
- ACL Information 432
- SNMP Commands 433
- DHCP Commands 447
- DHCP Relay 449
- DHCP Server 450
- DNS Commands 462
- Interface Commands 469
- Mirror Port Commands 480
- Rate Limit Commands 482
- Link Aggregation Commands 483
- Address Table Commands 492
- Spanning Tree Commands 496
- 497
- VLAN Commands 514
- Configuring VLAN Interfaces 516
- Displaying VLAN Information 521
- Priority Commands 532
- Quality of Service Commands 545
- Multicast Filtering Commands 554
- IGMP Commands (Layer 3) 562
- IP Interface Commands 569
- IP Routing Commands 576
- Global Routing Configuration 577
- ip-address 593
- Multicast Routing Commands 623
- Router Redundancy Commands 642
- Software Features 653
- Management Features 654
- Standards 654
- Management Information Bases 655
- Software Specifications 656
- Appendix B: Troubleshooting 657
- Using System Logs 658
- Glossary 659
- Glossary-8 666
- E032005-R02 674
Relacionado con productos y manuales para Los conmutadores de red Edge-Core ES3628C
(74 paginas)
(32 paginas)
(24 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.089 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales