Edge-Core WA6202AM EU Guía de usuario Pagina 185
- Pagina / 332
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
System Clock Commands
7-33
7
show event-log
This command displays log messages stored in the access point’s memory.
Syntax
show event-log
Command Mode
Exec
Example
System Clock Commands
These commands are used to configure SNTP and system clock settings on the
access point.
Enterprise AP#show event-log
Mar 09 11:57:55 Information: 802.11g:11g Radio Interface Enabled
Mar 09 11:57:55 Information: 802.11g:Radio channel updated to 8
Mar 09 11:57:34 Information: 802.11g:11g Radio Interface Enabled
Mar 09 11:57:18 Information: 802.11g:11g Radio Interface Enabled
Mar 09 11:56:35 Information: 802.11a:11a Radio Interface Enabled
Mar 09 11:55:52 Information: SSH task: Set SSH server port to 22
Mar 09 11:55:52 Information: SSH task: Enable SSH server.
Mar 09 11:55:52 Information: Enable Telnet.
Mar 09 11:55:40 Information: 802.11a:11a Radio Interface Disabled
Mar 09 11:55:40 Information: 802.11a:Transmit Power set to QUARTER
Press <n> next. <p> previous. <a> abort. <y> continue to end :
Enterprise AP#configure
Enter configuration commands, one per line. End with CTRL/Z
Enterprise AP(config)#logging clear
Table 7-7. System Clock Commands
Command Function Mode Page
sntp-server ip Specifies one or more time servers GC 7-34
sntp-server enable Accepts time from the specified time servers GC 7-34
sntp-server date-time Manually sets the system date and time GC 7-35
sntp-server
daylight-saving
Sets the start and end dates for daylight savings time GC 7-36
sntp-server timezone Sets the time zone for the access point’s internal clock GC 7-36
show sntp Shows current SNTP configuration settings Exec 7-37
- Powered by Accton 1
- User Guide 3
- WA6202AM 4
- F4.3.3.6 E112006-DT-R01 4
- 149100034900E 4
- Compliances 5
- VCCI Notice 6
- EC Conformance Declaration 6
- Community 6
- Safety Compliance 8
- Power Cord Set 9
- (Germany): 11
- <BASEC> tragen 12
- Table of Contents 13
- Chapter 1: Introduction 21
- Package Checklist 22
- Hardware Description 22
- LED Indicators 23
- Introduction 24
- Integrated High-Gain Antenna 25
- External Antenna Options 25
- Ethernet Port 26
- Power Injector Module 26
- Grounding Point 27
- Water Tight Test Point 27
- Features and Benefits 28
- Access Point Topologies 29
- Infrastructure Wireless LAN 30
- Point-to-Point Configuration 32
- Bridge Link Topologies 33
- Network Configuration 34
- Radio Path Planning 35
- Data Rates 35
- Antenna Height 36
- Bridge Link Planning 38
- Radio Interference 39
- Weather Conditions 39
- Grounding 40
- Testing Basic Link Operation 41
- Mount the Unit 41
- Mounting on a Pole 42
- Mounting to a Wall 44
- Connect External Antennas 45
- Connect Cables to the Unit 46
- Ground Wire 47
- Ethernet Cable 47
- Grounding Screw 47
- Align Antennas 48
- Hardware Installation 50
- Required Connections 51
- Initial Configuration Steps 52
- Logging In 53
- Initial Configuration 54
- Advanced Configuration 56
- System Identification 57
- TCP / IP Settings 59
- SSH Settings 65
- Authentication 66
- Filter Control 71
- WDS Settings 75
- AP Management 81
- Administration 82
- Setting the Timeout Interval 83
- Upgrading Firmware 83
- System Log 87
- Configuring SNTP 89
- Configuring SNMPv3 Users 100
- System Configuration 102
- Configuring SNMPv3 Targets 104
- Radio Interface 106
- Radio Settings A (802.11a) 107
- Normal Mode 114
- Turbo Mode 114
- Configuring Wi-Fi Multimedia 118
- Radio Settings G (802.11g) 124
- Security 127
- Enabling the VAPs 131
- Wi-Fi Protected Access (WPA) 137
- Configuring 802.1X 142
- Status Information 144
- Station Status 147
- Event Logs 149
- STP Status 151
- Chapter 7: Co 153
- Entering Commands 154
- Command Completion 155
- Getting Help on Commands 155
- Showing Commands 155
- Enterprise AP#show s? 156
- Enterprise AP#show s 156
- Exec Commands 157
- Configuration Commands 157
- Command Groups 158
- General Commands 159
- Command Line Interface 160
- System Management Commands 163
- APmgmtIP 173
- APmgmtUI 174
- System Logging Commands 180
- System Clock Commands 185
- DHCP Relay Commands 190
- SNMP Commands 192
- Flash/File Commands 207
- RADIUS Client 211
- 802.1X Authentication 217
- 802.1x-supplicant enable 218
- 802.1x-supplicant user 219
- MAC Address Authentication 221
- Filtering Commands 224
- WDS Bridge Commands 228
- Spanning Tree Commands 235
- Ethernet Interface Commands 240
- Wireless Interface Commands 245
- Rogue AP Detection Commands 266
- Wireless Security Commands 270
- Link Integrity Commands 280
- IAPP Commands 284
- VLAN Commands 285
- WMM Commands 287
- Appendix A: Troubleshooting 291
- Troubleshooting 292
- 10/100BASE-TX Pin Assignments 293
- Straight-Through Wiring 294
- Crossover Wiring 295
- 8-Pin DIN Connector Pinout 295
- Cables and Pinouts 296
- Appendix C: Specifications 297
- Specifications 298
- General Specifications 299
- Sensitivity 300
- Transmit Power 301
- 18 dBi High Gain Directional 302
- Panel (2.4GHz) 302
- 10 dBi Sector (2.4 GHz) 304
- 8 dBi Omnidirectional (5 GHz) 306
- V-förmige Halterung 313
- Montieren der Bridge 314
- Ethernet-Kabel 319
- Erdungsleitung 319
- Glossary 321
- Pub. Number: 149100034900E 332
- E112006-DT-R01 332
Relacionado con productos y manuales para Puntos de acceso wlan Edge-Core WA6202AM EU
(37 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.067 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales