Edge-Core WA6202AM EU Guía de usuario Pagina 237
- Pagina / 332
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Spanning Tree Commands
7-85
7
Example
bridge stp max-age
Use this command to configure the spanning tree bridge maximum age globally for
the wireless bridge. Use the no form to restore the default.
Syntax
bridge stp max-age <seconds>
no bridge stp max-age
seconds - Time in seconds. (Range: 6-40 seconds)
The minimum value is the higher of 6 or [2 x (hello-time + 1)].
The maximum value is the lower of 40 or [2 x (forward-time - 1)].
Default Setting
20 seconds
Command Mode
Global Configuration
Command Usage
This command sets the maximum time (in seconds) a device can wait without
receiving a configuration message before attempting to reconfigure. All device
ports (except for designated ports) should receive configuration messages at
regular intervals. Any port that ages out STP information (provided in the last
configuration message) becomes the designated port for the attached LAN. If
it is a root port, a new root port is selected from among the device ports
attached to the network.
Example
bridge stp priority
Use this command to configure the spanning tree priority globally for the wireless
bridge. Use the no form to restore the default.
Syntax
bridge stp priority<priority>
no bridge stp priority
priority - Priority of the bridge. (Range: 0 - 65535)
Default Setting
32768
Enterprise AP(config)#bridge stp hello-time 5
Enterprise AP(config)#
Enterprise AP(config)#bridge stp max-age 40
Enterprise AP(config)#
- Powered by Accton 1
- User Guide 3
- WA6202AM 4
- F4.3.3.6 E112006-DT-R01 4
- 149100034900E 4
- Compliances 5
- VCCI Notice 6
- EC Conformance Declaration 6
- Community 6
- Safety Compliance 8
- Power Cord Set 9
- (Germany): 11
- <BASEC> tragen 12
- Table of Contents 13
- Chapter 1: Introduction 21
- Package Checklist 22
- Hardware Description 22
- LED Indicators 23
- Introduction 24
- Integrated High-Gain Antenna 25
- External Antenna Options 25
- Ethernet Port 26
- Power Injector Module 26
- Grounding Point 27
- Water Tight Test Point 27
- Features and Benefits 28
- Access Point Topologies 29
- Infrastructure Wireless LAN 30
- Point-to-Point Configuration 32
- Bridge Link Topologies 33
- Network Configuration 34
- Radio Path Planning 35
- Data Rates 35
- Antenna Height 36
- Bridge Link Planning 38
- Radio Interference 39
- Weather Conditions 39
- Grounding 40
- Testing Basic Link Operation 41
- Mount the Unit 41
- Mounting on a Pole 42
- Mounting to a Wall 44
- Connect External Antennas 45
- Connect Cables to the Unit 46
- Ground Wire 47
- Ethernet Cable 47
- Grounding Screw 47
- Align Antennas 48
- Hardware Installation 50
- Required Connections 51
- Initial Configuration Steps 52
- Logging In 53
- Initial Configuration 54
- Advanced Configuration 56
- System Identification 57
- TCP / IP Settings 59
- SSH Settings 65
- Authentication 66
- Filter Control 71
- WDS Settings 75
- AP Management 81
- Administration 82
- Setting the Timeout Interval 83
- Upgrading Firmware 83
- System Log 87
- Configuring SNTP 89
- Configuring SNMPv3 Users 100
- System Configuration 102
- Configuring SNMPv3 Targets 104
- Radio Interface 106
- Radio Settings A (802.11a) 107
- Normal Mode 114
- Turbo Mode 114
- Configuring Wi-Fi Multimedia 118
- Radio Settings G (802.11g) 124
- Security 127
- Enabling the VAPs 131
- Wi-Fi Protected Access (WPA) 137
- Configuring 802.1X 142
- Status Information 144
- Station Status 147
- Event Logs 149
- STP Status 151
- Chapter 7: Co 153
- Entering Commands 154
- Command Completion 155
- Getting Help on Commands 155
- Showing Commands 155
- Enterprise AP#show s? 156
- Enterprise AP#show s 156
- Exec Commands 157
- Configuration Commands 157
- Command Groups 158
- General Commands 159
- Command Line Interface 160
- System Management Commands 163
- APmgmtIP 173
- APmgmtUI 174
- System Logging Commands 180
- System Clock Commands 185
- DHCP Relay Commands 190
- SNMP Commands 192
- Flash/File Commands 207
- RADIUS Client 211
- 802.1X Authentication 217
- 802.1x-supplicant enable 218
- 802.1x-supplicant user 219
- MAC Address Authentication 221
- Filtering Commands 224
- WDS Bridge Commands 228
- Spanning Tree Commands 235
- Ethernet Interface Commands 240
- Wireless Interface Commands 245
- Rogue AP Detection Commands 266
- Wireless Security Commands 270
- Link Integrity Commands 280
- IAPP Commands 284
- VLAN Commands 285
- WMM Commands 287
- Appendix A: Troubleshooting 291
- Troubleshooting 292
- 10/100BASE-TX Pin Assignments 293
- Straight-Through Wiring 294
- Crossover Wiring 295
- 8-Pin DIN Connector Pinout 295
- Cables and Pinouts 296
- Appendix C: Specifications 297
- Specifications 298
- General Specifications 299
- Sensitivity 300
- Transmit Power 301
- 18 dBi High Gain Directional 302
- Panel (2.4GHz) 302
- 10 dBi Sector (2.4 GHz) 304
- 8 dBi Omnidirectional (5 GHz) 306
- V-förmige Halterung 313
- Montieren der Bridge 314
- Ethernet-Kabel 319
- Erdungsleitung 319
- Glossary 321
- Pub. Number: 149100034900E 332
- E112006-DT-R01 332
Relacionado con productos y manuales para Puntos de acceso wlan Edge-Core WA6202AM EU
(37 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales